| Trailer Brakes |
|---|
|
20099
Engager Trailer BreakAway Kit with Charger and Tester
The Breakaway system is designed to bring trailers safely to a stop by activating electric brakes, should a trailer be disconnected while driving. This type of safety system is required in most states on trailers rated over 3,000 GVW. - Kit Includes:
- Battery Charger
- Weather Resistant Battery Box
- Sealed 12-Volt Rechargeable Battery
- Break-Away Switch
- L.E.D. Tester Shows if Battery is Good, Bad or Charging
- Box can be mounted on trailer jack or trailer frame.
- Works with single and tandem axle trailers
- Dimensions:
- 5-5/8" Wide x 5-1/8" Tall x 4-1/8" Deep
L.E.D. light glows when battery is charged.
|
20002
Trailer Breakaway Kit
The Breakaway system is designed to bring trailers safely to a stop by activating electric brakes, should a trailer be disconnected while driving. This type of safety system is required in most states on trailers rated over 3,000 GVW. - Kit Includes:
- Lockable Weather Resistant Battery Box
- Sealed 12-Volt Rechargeable Battery
- Break-Away Switch
- Box can be mounted on trailer jack or trailer frame.
- Works with single, tandem and tri axle trailers
Click Here for a trailer break-away kit with charger.
|
20001
Trailer Break-Away Kit with Charger
The Break-Away system is designed to bring trailers safely to a stop by activating electric brakes should a trailer be disconnected while driving. This type of safety system is required in most states on trailers rated over 3,000 GVW. - Kit Includes:
- Battery Charger
- Lockable Weather Resistant Battery Box
- Sealed 12-Volt Rechargeable Battery
- Break-Away Switch
- Box can be mounted on trailer jack or trailer frame.
- Works with single, tandem and tri axle trailers.
|
420000
Replacement Tekonsha Trailer Breakaway Switch
Replacement Trailer Break away switch for Tekonsha Breakaway Kit - 2010
|
23-47
7" Electric Brake Assembly for 2K Axles - LH
Dexter 7" x 1-1/4" Left Hand Electric Brake Assembly - 2,000 lbs. Capacity per Pair
- Mounts with 4 Bolts
|
23-48
7" Electric Brake Assembly for 2K Axles - RH
Dexter 7" x 1-1/4" Left Hand Electric Brake Assembly - 2,000 lbs. Capacity per Pair
|
BP04-040
7" x 1-1/4" Brake Shoe/Lining (One Wheel)
Replacement brake shoes for Dexter 7" x 1-1/4" brake assemblies. Works with assemblies #23-47 and #23-48. 
|
23-26
10" Electric Brake Assembly LH
Dexter 10" x 2-1/4" Left Hand Electric Brake Assembly - 3,500 lbs. Capacity per Pair
- Mounts with 4 Bolts
- Bolt holes are 2-7/8" apart, center to center
- Uses 10" Hub/Drums
|
23-27
10" Electric Brake Assembly RH
Dexter 10" x 2-1/4" Right Hand Electric Brake Assembly - 3,500 lbs. Capacity per Pair
- Mounts with 4 Bolts
- Bolt holes are 2-7/8" apart, center to center
- Uses 10" Hub/Drums
|
BP04-090
10" x 2-1/4" Brake Shoe/Lining (One Wheel)
- Fits: Dexter, Fayette, and Foreman 10" x 2-1/4" Electric Brakes
|
23-312
10" x 2-1/4" Hydraulic Brake Assembly - LH
Single-Servo 10" x 2-1/4" Hydraulic Brake Assembly - 3,500 lbs. Capacity per Pair
- Single Servo - Single plunger comes from the wheel cylinder (Most Common Style)
- Uses 7" Hub/Drums
|
23-313
10" x 2-1/4" Hydraulic Brake Assembly - RH
Single-Servo 10" x 2-1/4" Right Handed Hydraulic Brake Assembly - 3,500 lbs. Capacity per Pair
- Single Servo - Single plunger comes from the wheel cylinder (Most Common Style)
- Uses 10" Hub/Drums
|
BP04-120
10" X 2-1/4" Hydraulic Brake Shoe/Lining (One Wheel)
Trailer Brake Shoe Pads for hydraulic trailer brakes - Fits: Atwood, Bendix, Dexter, and Dico 10" X 2-1/4" Hydraulic Brakes
|
23-105
12" Electric Brake Assembly LH
Dexter 12" x 2" Left Hand Electric Brake Assembly - 6,000 lbs. Capacity per Pair
- Mounts with 5 Bolts
|
23-106
12" Electric Brake Assembly RH
Dexter 12" x 2" Right Hand Electric Brake Assembly - 6,000 lbs. Capacity per Pair
- Mounts with 5 Bolts
|
BP04-150
12" X 2" Trailer Brake Shoe / Lining (One Wheel)
Trailer Brake Assembly Shoes - Fits: Dexter, Fayette, and Foreman 12" X 2" Electric Brakes
|
23-324
12" x 2" Hydraulic Brake Assembly - LH
Single-Servo 12" x 2" Hydraulic Brake Assembly - 5,200 lbs. Capacity per Pair
- Single Servo - Single plunger comes from the wheel cylinder (Most Common Style)
|
23-325
12" x 2" Hydraulic Brake Assembly - RH
Single-Servo 12" x 2" Right Handed Hydraulic Brake Assembly - 5,200 lbs. Capacity per Pair
- Single Servo - Single plunger comes from the wheel cylinder (Most Common Style)
|
116200
5 on 4-1/2" Hub / Drum Assembly - 2,000 lbs.
- Used on Dexter and Most 2000 lbs. Axles with 1-1/16" Spindle, L44649 Inner / Outer Bearings
- Capacity of 1,750 lbs. per each
- Drum Size: 7" x 1-3/4"
- Bolt Pattern: 5 on 4-1/2 (for information see below)
- Bearings, Races, Cap, and Seal Included
   |  | | Typical Photos | Note: Most trailer tires that are smaller than 15" and have 5 bolts, have a 5 on 4-1/2" bolt pattern. How to Measure Bolt Pattern |  | Determine the bolt pattern on the trailer wheel by the number of bolts and the bolt circle. To determine the bolt circle on wheels with an even number of bolt holes, measure center-to-center on bolt holes directly across from each other on the diameter (Example: 8 on 6-1/2 would mean 8 bolt holes with 6-1/2" center-to-center diameter). On odd number bolt wheels, measure any bolt hole center to the point halfway between bolt holes on the diameter (Example: 5 on 4-1/2 would mean 5 bolt holes with 4-1/2" measured to a point halfway between the opposite bolts). | AND / OR |  | The distance between the center of one bolt hole on the wheel to the center of the bolt hole right next to it will also help determine the bolt pattern. - If D = 2-5/8" then the bolt pattern is a 5 on 4-1/2
- If D = 2-3/4" then the bolt pattern is a 5 on 4-3/4
- If D = 3" then the bolt pattern is a 5 on 5
- If D = 3-1/4" then the bolt pattern is a 5 on 5-1/2
|
|
84546UC3
5 on 4-1/2 Hub/Drum Kit - 3,500 lbs.
- Used on Dexter and Most 3,500 lbs. Axles
- Capacity of 1,750 lbs. per each
- Drum Size: 10" x 2-1/4"
- Bolt Pattern: 5 on 4-1/2 (for information see below)
- Bearings, Races, Cap, and Seal Included (L68149 Inner / L44649 Outer Bearings)
Note: Most trailer tires that are smaller than 15" and have 5 bolts, have a 5 on 4-1/2" bolt pattern. How to Measure Bolt Pattern | | | Determine the bolt pattern on the trailer wheel by the number of bolts and the bolt circle. To determine the bolt circle on wheels with an even number of bolt holes, measure center-to-center on bolt holes directly across from each other on the diameter (Example: 8 on 6-1/2 would mean 8 bolt holes with 6-1/2" center-to-center diameter). On odd number bolt wheels, measure any bolt hole center to the point halfway between bolt holes on the diameter (Example: 5 on 4-1/2 would mean 5 bolt holes with 4-1/2" measured to a point halfway between the opposite bolts). | AND / OR | | | The distance between the center of one bolt hole on the wheel to the center of the bolt hole right next to it will also help determine the bolt pattern. - If D = 2-5/8" then the bolt pattern is a 5 on 4-1/2
- If D = 2-3/4" then the bolt pattern is a 5 on 4-3/4
- If D = 3" then the bolt pattern is a 5 on 5
- If D = 3-1/4" then the bolt pattern is a 5 on 5-1/2
|
|
845476UC3
5 on 4-3/4 Hub/Drum Kit - 3,500 lbs.
- Used on Dexter and Most 3,500 lbs. Axles
- Capacity of 1,750 lbs. per each
- Drum Size: 10" x 2-1/4"
- Bolt Pattern: 5 on 4-3/4 (for information see below)
- Bearings, Races, Cap, and Seal Included (L68149 Inner / L44649 Outer Bearings)
Note: Most trailer tires that are smaller than 15" and have 5 bolts, have a 5 on 4-1/2" bolt pattern. How to Measure Bolt Pattern | | | Determine the bolt pattern on the trailer wheel by the number of bolts and the bolt circle. To determine the bolt circle on wheels with an even number of bolt holes, measure center-to-center on bolt holes directly across from each other on the diameter (Example: 8 on 6-1/2 would mean 8 bolt holes with 6-1/2" center-to-center diameter). On odd number bolt wheels, measure any bolt hole center to the point halfway between bolt holes on the diameter (Example: 5 on 4-1/2 would mean 5 bolt holes with 4-1/2" measured to a point halfway between the opposite bolts). | AND / OR | | | The distance between the center of one bolt hole on the wheel to the center of the bolt hole right next to it will also help determine the bolt pattern. - If D = 2-5/8" then the bolt pattern is a 5 on 4-1/2
- If D = 2-3/4" then the bolt pattern is a 5 on 4-3/4
- If D = 3" then the bolt pattern is a 5 on 5
- If D = 3-1/4" then the bolt pattern is a 5 on 5-1/2
|
|
84556UC3
5 on 5 Hub/Drum Kit - 3,500 lbs.
- Used on Dexter and Most 3,500 lbs. Axles
- Capacity of 1,750 lbs. per each
- Drum Size: 10" x 2-1/4"
- Bolt Pattern: 5 on 5(for information see below)
- Bearings, Races, Cap, and Seal Included (L68149 Inner / L44649 Outer Bearings)
Note: Most trailer tires that are smaller than 15" and have 5 bolts, have a 5 on 4-1/2" bolt pattern. How to Measure Bolt Pattern | | | Determine the bolt pattern on the trailer wheel by the number of bolts and the bolt circle. To determine the bolt circle on wheels with an even number of bolt holes, measure center-to-center on bolt holes directly across from each other on the diameter (Example: 8 on 6-1/2 would mean 8 bolt holes with 6-1/2" center-to-center diameter). On odd number bolt wheels, measure any bolt hole center to the point halfway between bolt holes on the diameter (Example: 5 on 4-1/2 would mean 5 bolt holes with 4-1/2" measured to a point halfway between the opposite bolts). | AND / OR | | | The distance between the center of one bolt hole on the wheel to the center of the bolt hole right next to it will also help determine the bolt pattern. - If D = 2-5/8" then the bolt pattern is a 5 on 4-1/2
- If D = 2-3/4" then the bolt pattern is a 5 on 4-3/4
- If D = 3" then the bolt pattern is a 5 on 5
- If D = 3-1/4" then the bolt pattern is a 5 on 5-1/2
|
|
84557UC3
5 on 5-1/2 Hub/Drum Kit - 3,500 lbs.
- Used on Dexter and Most 3,500 lbs. Axles
- Capacity of 1,750 lbs. per each
- Drum Size: 10" x 2-1/4"
- Bolt Pattern: 5 on 5-1/2 (for information see below)
- Bearings, Races, Cap, and Seal Included (L68149 Inner / L44649 Outer Bearings)
Note: Most trailer tires that are smaller than 15" and have 5 bolts, have a 5 on 4-1/2" bolt pattern. How to Measure Bolt Pattern | | | Determine the bolt pattern on the trailer wheel by the number of bolts and the bolt circle. To determine the bolt circle on wheels with an even number of bolt holes, measure center-to-center on bolt holes directly across from each other on the diameter (Example: 8 on 6-1/2 would mean 8 bolt holes with 6-1/2" center-to-center diameter). On odd number bolt wheels, measure any bolt hole center to the point halfway between bolt holes on the diameter (Example: 5 on 4-1/2 would mean 5 bolt holes with 4-1/2" measured to a point halfway between the opposite bolts). | AND / OR | | | The distance between the center of one bolt hole on the wheel to the center of the bolt hole right next to it will also help determine the bolt pattern. - If D = 2-5/8" then the bolt pattern is a 5 on 4-1/2
- If D = 2-3/4" then the bolt pattern is a 5 on 4-3/4
- If D = 3" then the bolt pattern is a 5 on 5
- If D = 3-1/4" then the bolt pattern is a 5 on 5-1/2
|
|
42656
6 on 5-1/2 Hub/Drum - 5,200 & 6,000 lbs. Axles
- Used on Dexter 5,200 lbs. and 6,000 lbs. Axles, Or on Spindles requiring a 2-1/8" or 2-1/4" I.D. Grease Seal
- Capacity of 3,000 lbs. per each
- Drum Size: 12" x 2"
- Bolt Pattern: 6 on 5-1/2 (for information see below)
- Bearings, Races, Cap, and Seal Not Included
 | | | | Typical Photos | How to Measure Bolt Pattern | | | Determine the bolt pattern by the number of bolts and the bolt circle. To determine the bolt circle on wheels with an even number of bolt holes, measure center-to-center on bolt holes directly across from each other on the diameter (Example: 8 on 6-1/2 would mean 8 bolt holes with 6-1/2" center-to-center diameter). On odd number bolt wheels, measure any bolt hole center to the point halfway between bolt holes on the diameter (Example: 5 on 4-1/2 would mean 5 bolt holes with 4-1/2" measured to a point halfway between the opposite bolts). |
|
9504
Hydraulic Line Kit - Single Axle - Drum
Hydraulic Line Kits comes complete with all necessary lines, tee fittings, hoses, brackets and clips to properly plumb hydraulic brake axles.  - 3/16" x 180" corrosion resistant hydraulic steel brake line
- Brake line is plated inside and out and features an electro-deposition zinc plating process. A special additional post-plating treatment greatly extends the life of the product even further.
Note: Torsion Axles require additional line kits (80910 or 80910-T) or use 9579-2 Deluxe kit with limited access flex hoses included.
|
9505
Hydraulic Line Kit - Tandem Axle - Drum
Hydraulic Line Kits comes complete with all necessary lines, tee fittings, hoses, brackets and clips to properly plumb hydraulic brake axles.  Torsion Axles require additional line kits (80910 or 80910-T) or use 9579-2 Deluxe kit with limited access flex hoses included.
|
9579-2
Deluxe Hydraulic Line Kit - Tandem Axle - Drum
Hydraulic Line Kits comes complete with all necessary lines, tee fittings, hoses, brackets and clips to properly plumb hydraulic brake axles. Line kit will work on Deluxe Drum trailer brakes and 3.5K - 8K trailer Disc brakes. - 3 - 3/16" Service Tees
- 1 - 3/16" Hydraulic Union
- 4 - Hose Brackets
- 4 - Hose Clips
- 2 - Line Tie Straps
- 6 - Line Retaining Clips
- 6 - Line Retaining Clip Screws
- 2 - 3/16" x 180" Steel Lines
- 4 - 90 Degree Flex Hoses
- 2 - 3/16" x 51" Steel Lines
- 1 - 3/16" x 72" Steel Line
|
BP01-110
Trailer Brake Magnet for 10" Hub/Drums
Trailer Brake Magnet for 10" Hubs - Fits:
- Dexter 10" x 2.25"
- Hayes (after 1988) 10" x 2.25"
- Alko 10" x 2.25"
|
BP01-180
Trailer Brake Magnet for 12" Hub/Drums
Trailer Brake Magnet for 12" Hub/Drum - Fits:
- Dexter 12" x 2" 6K
- Alko 12" x 2" 6K & 7K after 1988(not centerline)
- Hayes 12" x 2" 6K & 7K after 1988(not centerline)
|
BP01-160
Trailer Brake Magnet for 12" Hayes
Trailer Brake Magnet for Hayes 12" x 2" Round Old Style (before 1988)
|
BP17-030
Wheel Cylinder - 10" & 12" Single Serve LH
Replacement Wheel Cylinder for 10" and 12" left handed single serve brake assemblies manufactured by Dexter, Bendix, Dico, Demco or Atwood.
|
BP17-020
Wheel Cylinder - 10" & 12" Single Serve RH
Replacement Wheel Cylinder for 10" and 12" right handed single serve brake assemblies manufactured by Dexter, Bendix, Dico, Demco or Atwood.
|
